NAME
tclsh - Simple shell containing Tcl interpreter
SYNOPSIS
tclsh ?-encoding name? ?fileName arg arg ...?
_________________________________________________________________
DESCRIPTION
Tclsh is a shell-like application that reads Tcl commands from its
standard input or from a file and evaluates them. If invoked with no
arguments then it runs interactively, reading Tcl commands from
standard input and printing command results and error messages to
standard output. It runs until the exit command is invoked or until it
reaches end-of-file on its standard input. If there exists a file
.tclshrc (or tclshrc.tcl on the Windows platforms) in the home
directory of the user, interactive tclsh evaluates the file as a Tcl
script just before reading the first command from standard input.
SCRIPT FILES
If tclsh is invoked with arguments then the first few arguments specify │
the name of a script file, and, optionally, the encoding of the text │
data stored in that script file. Any additional arguments are made
available to the script as variables (see below). Instead of reading
commands from standard input tclsh will read Tcl commands from the
named file; tclsh will exit when it reaches the end of the file. The
end of the file may be marked either by the physical end of the medium,
or by the character, “\032” (“\u001a”, control-Z). If this character
is present in the file, the tclsh application will read text up to but
not including the character. An application that requires this
character in the file may safely encode it as “\032”, “\x1a”, or
“\u001a”; or may generate it by use of commands such as format or
binary. There is no automatic evaluation of .tclshrc when the name of
a script file is presented on the tclsh command line, but the script
file can always source it if desired.
If you create a Tcl script in a file whose first line is
#!/usr/local/bin/tclsh
then you can invoke the script file directly from your shell if you
mark the file as executable. This assumes that tclsh has been
installed in the default location in /usr/local/bin; if it is
installed somewhere else then you will have to modify the above line to
match. Many UNIX systems do not allow the #! line to exceed about 30
characters in length, so be sure that the tclsh executable can be
accessed with a short file name.
An even better approach is to start your script files with the
following three lines:
#!/bin/sh
# the next line restarts using tclsh \
exec tclsh "$0" "$@"
This approach has three advantages over the approach in the previous
paragraph. First, the location of the tclsh binary does not have to be
hard-wired into the script: it can be anywhere in your shell search
path. Second, it gets around the 30-character file name limit in the
previous approach. Third, this approach will work even if tclsh is
itself a shell script (this is done on some systems in order to handle
multiple architectures or operating systems: the tclsh script selects
one of several binaries to run). The three lines cause both sh and
tclsh to process the script, but the exec is only executed by sh. sh
processes the script first; it treats the second line as a comment and
executes the third line. The exec statement cause the shell to stop
processing and instead to start up tclsh to reprocess the entire
script. When tclsh starts up, it treats all three lines as comments,
since the backslash at the end of the second line causes the third line
to be treated as part of the comment on the second line.
You should note that it is also common practice to install tclsh with
its version number as part of the name. This has the advantage of
allowing multiple versions of Tcl to exist on the same system at once,
but also the disadvantage of making it harder to write scripts that
start up uniformly across different versions of Tcl.
VARIABLES
Tclsh sets the following Tcl variables:
argc Contains a count of the number of arg arguments (0 if
none), not including the name of the script file.
argv Contains a Tcl list whose elements are the arg
arguments, in order, or an empty string if there are no
arg arguments.
argv0 Contains fileName if it was specified. Otherwise,
contains the name by which tclsh was invoked.
tcl_interactive
Contains 1 if tclsh is running interactively (no
fileName was specified and standard input is a terminal-
like device), 0 otherwise.
PROMPTS
When tclsh is invoked interactively it normally prompts for each
command with “% ”. You can change the prompt by setting the variables
tcl_prompt1 and tcl_prompt2. If variable tcl_prompt1 exists then it
must consist of a Tcl script to output a prompt; instead of outputting
a prompt tclsh will evaluate the script in tcl_prompt1. The variable
tcl_prompt2 is used in a similar way when a newline is typed but the
current command is not yet complete; if tcl_prompt2 is not set then no
prompt is output for incomplete commands.
STANDARD CHANNELS
See Tcl_StandardChannels for more explanations.
SEE ALSO
encoding(3tcl), fconfigure(3tcl), tclvars(3tcl)
KEYWORDS
argument, interpreter, prompt, script file, shell