NAME
cat - concatenate and print files
SYNOPSIS
cat [-u][file ...]
DESCRIPTION
The cat utility shall read files in sequence and shall write their
contents to the standard output in the same sequence.
OPTIONS
The cat utility shall conform to the Base Definitions volume of
IEEE Std 1003.1-2001, Section 12.2, Utility Syntax Guidelines.
The following option shall be supported:
-u Write bytes from the input file to the standard output without
delay as each is read.
OPERANDS
The following operand shall be supported:
file A pathname of an input file. If no file operands are specified,
the standard input shall be used. If a file is ’-’ , the cat
utility shall read from the standard input at that point in the
sequence. The cat utility shall not close and reopen standard
input when it is referenced in this way, but shall accept
multiple occurrences of ’-’ as a file operand.
STDIN
The standard input shall be used only if no file operands are
specified, or if a file operand is ’-’ . See the INPUT FILES section.
INPUT FILES
The input files can be any file type.
ENVIRONMENT VARIABLES
The following environment variables shall affect the execution of cat:
LANG Provide a default value for the internationalization variables
that are unset or null. (See the Base Definitions volume of
IEEE Std 1003.1-2001, Section 8.2, Internationalization
Variables for the precedence of internationalization variables
used to determine the values of locale categories.)
LC_ALL If set to a non-empty string value, override the values of all
the other internationalization variables.
LC_CTYPE
Determine the locale for the interpretation of sequences of
bytes of text data as characters (for example, single-byte as
opposed to multi-byte characters in arguments).
LC_MESSAGES
Determine the locale that should be used to affect the format
and contents of diagnostic messages written to standard error.
NLSPATH
Determine the location of message catalogs for the processing of
LC_MESSAGES .
ASYNCHRONOUS EVENTS
Default.
STDOUT
The standard output shall contain the sequence of bytes read from the
input files. Nothing else shall be written to the standard output.
STDERR
The standard error shall be used only for diagnostic messages.
OUTPUT FILES
None.
EXTENDED DESCRIPTION
None.
EXIT STATUS
The following exit values shall be returned:
0 All input files were output successfully.
>0 An error occurred.
CONSEQUENCES OF ERRORS
Default.
The following sections are informative.
APPLICATION USAGE
The -u option has value in prototyping non-blocking reads from FIFOs.
The intent is to support the following sequence:
mkfifo foo
cat -u foo > /dev/tty13 &
cat -u > foo
It is unspecified whether standard output is or is not buffered in the
default case. This is sometimes of interest when standard output is
associated with a terminal, since buffering may delay the output. The
presence of the -u option guarantees that unbuffered I/O is available.
It is implementation-defined whether the cat utility buffers output if
the -u option is not specified. Traditionally, the -u option is
implemented using the equivalent of the setvbuf() function defined in
the System Interfaces volume of IEEE Std 1003.1-2001.
EXAMPLES
The following command:
cat myfile
writes the contents of the file myfile to standard output.
The following command:
cat doc1 doc2 > doc.all
concatenates the files doc1 and doc2 and writes the result to doc.all.
Because of the shell language mechanism used to perform output
redirection, a command such as this:
cat doc doc.end > doc
causes the original data in doc to be lost.
The command:
cat start - middle - end > file
when standard input is a terminal, gets two arbitrary pieces of input
from the terminal with a single invocation of cat. Note, however, that
if standard input is a regular file, this would be equivalent to the
command:
cat start - middle /dev/null end > file
because the entire contents of the file would be consumed by cat the
first time ’-’ was used as a file operand and an end-of-file condition
would be detected immediately when ’-’ was referenced the second time.
RATIONALE
Historical versions of the cat utility include the options -e, -t, and
-v, which permit the ends of lines, <tab>s, and invisible characters,
respectively, to be rendered visible in the output. The standard
developers omitted these options because they provide too fine a degree
of control over what is made visible, and similar output can be
obtained using a command such as:
sed -n -e ’s/$/$/’ -e l pathname
The -s option was omitted because it corresponds to different functions
in BSD and System V-based systems. The BSD -s option to squeeze blank
lines can be accomplished by the shell script shown in the following
example:
sed -n ’
# Write non-empty lines.
/./ {
p
d
}
# Write a single empty line, then look for more empty lines.
/^$/ p
# Get next line, discard the held <newline> (empty line),
# and look for more empty lines.
:Empty
/^$/ {
N
s/.//
b Empty
}
# Write the non-empty line before going back to search
# for the first in a set of empty lines.
p
The System V -s option to silence error messages can be accomplished by
redirecting the standard error. Note that the BSD documentation for cat
uses the term "blank line" to mean the same as the POSIX "empty line’’:
a line consisting only of a <newline>.
The BSD -n option was omitted because similar functionality can be
obtained from the -n option of the pr utility.
FUTURE DIRECTIONS
None.
SEE ALSO
more , the System Interfaces volume of IEEE Std 1003.1-2001, setvbuf()
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form
from IEEE Std 1003.1, 2003 Edition, Standard for Information Technology
-- Portable Operating System Interface (POSIX), The Open Group Base
Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of
Electrical and Electronics Engineers, Inc and The Open Group. In the
event of any discrepancy between this version and the original IEEE and
The Open Group Standard, the original IEEE and The Open Group Standard
is the referee document. The original Standard can be obtained online
at http://www.opengroup.org/unix/online.html .